Protecting your home or shed from electrical surges and lightning strikes is important. Using a grounding rod is needed for this to work properly. It is easy to install, though it does take a bit of effort and some special tools. There may be specific rules in your area on how and where they need to be installed, so be sure to check with a local utility company. It is also very important to have them come out and mark where other lines are to avoid electrocution or damaging other lines.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
The next step is to dig the hole. Avoid rocky areas or any places that the utility company marked for other lines. The spot you pick should be between one and two feet from the building for it to work the best. If it is too close, it can reduce the effectiveness by putting the surge back into the building.
Next, start digging. If you have the post hole digger, you can use it to get a few feet down. These are better than shovels because you do not need a wide hole, but a deep one. If you only have a shovel it will do, but the hole won't be as deep. Either way, you will get a good start and be on your way.
Once the hole is deep enough to start, add water. This will help soften the soil and make the rest of the job a bit easier. Place the rod in the hole and start pushing it around. One end should be pointed and this is the end that goes into the ground first. As you push it, you may add more water to help soften the dirt even more. Eventually, you will need to use a mallet, hammer or driver to complete the job of putting the rod all the way into the ground.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
Now you want to attach a ground wire. This will also be attached to your electrical panel, so be sure to handle with care. Some are shielded wires, so you will need to cut the end and expose the copper wire. Use a special clamp to connect to the pole. Make sure there is enough slack in the wire that bumping it will not disconnect it from the rod. You may want to dig a small trench to bury the wire it if is in an area that will be mowed and away from the house a few feet.
Fill in the hole and finish the job. Some areas require the rod to be completely underground and others don't have a rule. It is best to keep it low enough that the lawn mower won't hit it. If it is in an area that will be mowed, it is a good idea to bury the connecting wire as well as the rod completely under the ground.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
The next step is to dig the hole. Avoid rocky areas or any places that the utility company marked for other lines. The spot you pick should be between one and two feet from the building for it to work the best. If it is too close, it can reduce the effectiveness by putting the surge back into the building.
Next, start digging. If you have the post hole digger, you can use it to get a few feet down. These are better than shovels because you do not need a wide hole, but a deep one. If you only have a shovel it will do, but the hole won't be as deep. Either way, you will get a good start and be on your way.
Once the hole is deep enough to start, add water. This will help soften the soil and make the rest of the job a bit easier. Place the rod in the hole and start pushing it around. One end should be pointed and this is the end that goes into the ground first. As you push it, you may add more water to help soften the dirt even more. Eventually, you will need to use a mallet, hammer or driver to complete the job of putting the rod all the way into the ground.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
Now you want to attach a ground wire. This will also be attached to your electrical panel, so be sure to handle with care. Some are shielded wires, so you will need to cut the end and expose the copper wire. Use a special clamp to connect to the pole. Make sure there is enough slack in the wire that bumping it will not disconnect it from the rod. You may want to dig a small trench to bury the wire it if is in an area that will be mowed and away from the house a few feet.
Fill in the hole and finish the job. Some areas require the rod to be completely underground and others don't have a rule. It is best to keep it low enough that the lawn mower won't hit it. If it is in an area that will be mowed, it is a good idea to bury the connecting wire as well as the rod completely under the ground.
About the Author:
Find out how to get a high-quality grounding rod by viewing our web pages today. To access our online catalog of high voltage equipment or to learn more about our certifications, click the links at http://www.rossengineeringcorp.com .
Post A Comment:
0 comments:
Thanx for viewing us